CipherLab 1502 Specifiche Pagina 22
- Pagina / 174
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
8
Enter Setup
1500/1502 Barcode Scanner User Guide
READ A SETUP BARCODE
CONFIGURE PARAMETERS
For most of the scanner parameters, only one read is required to set them to new values.
The scanner will respond with two beeps (low-high tone) when each parameter is set
successfully.
But for a number of special parameters, multiple reads are required to complete the
setting. In this case, the scanner will respond with a short beep to indicate it needs to
read more setup barcodes. These special parameters may require reading one or more
setup barcodes, such as
Numeric barcodes, say, for keyboard type, inter-character delay, length qualification
Hexadecimal barcodes, say, for character strings as prefix, suffix, etc.
When “Keyboard Wedge” is configured for interface, Key Type and Key Status will
then become applicable. You may decide whether or not to change key status when
“Normal Key” is selected for Key Type.
To complete the configuration of these special parameters, it requires reading the
“Validate” barcode, and the scanner will respond with two beeps (low-high tone) to
indicate the input values are validated.
- 1500/1502 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 9
- INTRODUCTION 15
- SYMBOLOGIES SUPPORTED 17
- QUICK START 19
- ENTER CONFIGURATION MODE 20
- EXIT CONFIGURATION MODE 20
- Quick Start 21
- Refer to Appendix III 25
- LIST THE CURRENT SETTINGS 26
- ONE-SCAN SETUP BARCODES 28
- Chapter 1 29
- Chapter 1 31
- 1.4.2 GOOD READ BEEP 32
- 1.5 SEND “NR” TO HOST 33
- 1.6 SCAN MODES 34
- 1.6.6 ALTERNATE MODE 37
- 1.6.7 AIMING MODE 37
- 1.6.8 MULTI-BARCODE MODE 38
- 1.8 DELAY BETWEEN RE-READ 40
- Continuous mode 40
- Auto Power Off mode 40
- Alternate mode 40
- Addon Security Level 42
- 1.12 NEGATIVE BARCODES 44
- 1.13 EFFECTIVE DECODING AREA 45
- 1.13.1 POSITIONING WINDOW 45
- 1.13.2 ADJUSTING WINDOW 46
- Chapter 2 47
- 2.1 KEYBOARD WEDGE 48
- Chapter 2 49
- Selecting Output Interface 49
- *Capital Lock OFF 54
- 2.1.3 INTER-CHARACTER DELAY 58
- 2.1.4 INTER-FUNCTION DELAY 58
- 2.2 RS-232 59
- 2.2.2 BAUD RATE 59
- 2.2.3 DATA BITS 60
- 2.2.4 PARITY 60
- 2.2.5 STOP BIT 60
- 2.2.6 FLOW CONTROL 61
- 2.2.7 INTER-CHARACTER DELAY 62
- 2.2.8 INTER-FUNCTION DELAY 62
- 2.2.9 ACK/NAK TIMEOUT 63
- 2.3 WAND EMULATION 64
- 2.3.2 NORMAL STATE 64
- 2.3.3 BAR STATE 64
- 2.3.4 MODULE TIME 65
- 2.3.5 MARGIN TIME 66
- 2.3.6 OUTPUT FORMAT 67
- Chapter 3 69
- 3.1 CODABAR 70
- 3.1.1 SECURITY LEVEL 70
- 3.1.4 CLSI CONVERSION 71
- 3.2 CODE 25 – INDUSTRIAL 25 72
- 3.2.2 VERIFY CHECK DIGIT 73
- 3.2.3 TRANSMIT CHECK DIGIT 73
- 3.3 CODE 25 – INTERLEAVED 25 75
- 3.3.2 VERIFY CHECK DIGIT 76
- 3.3.3 TRANSMIT CHECK DIGIT 76
- 3.4 CODE 25 – MATRIX 25 78
- 3.4.2 VERIFY CHECK DIGIT 79
- 3.4.3 TRANSMIT CHECK DIGIT 79
- 3.5 CODE 39 81
- 3.5.2 VERIFY CHECK DIGIT 81
- 3.5.3 TRANSMIT CHECK DIGIT 82
- 3.5.5 SECURITY LEVEL 82
- 3.6 CODE 93 83
- 3.7 CODE 128 83
- 3.7.1 SECURITY LEVEL 83
- 3.8 EAN-8 84
- 3.8.1 CONVERT TO EAN-13 85
- 3.8.2 TRANSMIT CHECK DIGIT 85
- 3.8.3 CONVERSION FORMAT 85
- 3.9 EAN-13 86
- 3.9.1 CONVERT TO ISBN 87
- 3.9.2 CONVERT TO ISSN 87
- 3.9.3 TRANSMIT CHECK DIGIT 87
- 3.9.4 SECURITY LEVEL 88
- *Disable 90
- 3.10 GS1-128 (EAN-128) 91
- 3.10.1 TRANSMIT CODE ID 91
- 3.10.3 GS1 FORMATTING 92
- 3.10.4 APPLICATION ID MARK 92
- 3.12 MSI 94
- 3.12.1 VERIFY CHECK DIGIT 94
- 3.12.2 TRANSMIT CHECK DIGIT 94
- 3.13 FRENCH PHARMACODE 96
- 3.13.1 TRANSMIT CHECK DIGIT 96
- 3.14 ITALIAN PHARMACODE 97
- 3.14.1 TRANSMIT CHECK DIGIT 97
- 3.15 PLESSEY 98
- 3.15.1 CONVERT TO UK PLESSEY 98
- 3.15.2 TRANSMIT CHECK DIGIT 98
- Chapter 3 101
- Changing Symbology Settings 101
- GS1 DataBar Expanded 102
- 3.16.6 GS1 FORMATTING 104
- 3.16.7 APPLICATION ID MARK 104
- 3.17 TELEPEN 105
- 3.18 UPC-A 106
- 3.18.3 TRANSMIT CHECK DIGIT 107
- 3.18.1 CONVERT TO EAN-13 107
- 3.19 UPC-E 108
- 3.19.4 TRANSMIT CHECK DIGIT 110
- Chapter 4 111
- Chapter 4 113
- Defining Output Format 113
- 4.4.2 CHANGE CODE ID 123
- 4.4.3 CLEAR CODE ID SETTINGS 124
- 4.5 LENGTH CODE 125
- 4.6 MULTI-BARCODE EDITOR 129
- Code Type 129
- Enter Setup 132
- Remove Special 132
- Character 132
- Chapter 5 133
- 5.1.2 EXCLUSIVE DATA EDITING 135
- End Programming Format 136
- 5.2.2 RESTORE DEFAULT FORMAT 138
- 5.3.1 APPLICABLE CODE TYPE 139
- 131 145
- 5.3.2 DATA LENGTH 146
- 5.4.3 TOTAL NUMBER OF FIELDS 149
- 5.4.4 FIELD SETTINGS 150
- Field 3 Setting 152
- 139 153
- Field 4 Setting 153
- Field 5 Setting 154
- 141 155
- Additional Fields 155
- Key Type Key Status 155
- 5.4.5 PAUSE FIELD SETTING 156
- 5.6 PROGRAMMING EXAMPLES 159
- 5.6.1 EXAMPLE I 159
- SPECIFICATIONS 161
- Resistance 162
- Programming Support 162
- Appendix I 163
- Appendix II 165
- Appendix III 167
- KEY TYPE & STATUS 168
- KEY TYPE 168
- KEY STATUS 168
- EXAMPLE 169
- Appendix IV 171
- HEXADECIMAL SYSTEM 172
- ASCII TABLE 173
Prodotti e manuali riguardandi Lettori di codici a barre CipherLab 1502
Lettori di codici a barre CipherLab 1266 Specifiche
(180 pagine)
(180 pagine)
(277 pagine)
Lettori di codici a barre CipherLab 1660 Specifiche
(156 pagine)
(156 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale